
Commercial HVAC Maintenance for Silicon Valley Offices
February 12, 2026

Most of the roofs sitting on top of Silicon Valley's commercial buildings are low-slope systems (TPO, EPDM, or modified bitumen) and most of them were installed to handle exactly the load they're getting right now: nine dry months of UV exposure followed by three months of intense, wind-driven rain squeezed into a handful of atmospheric river events. That compressed rainy season is unforgiving. A membrane seam that's been slowly failing since April won't show it until the first real storm in November, and by then water has already found its way into a ceiling tile above someone's desk, a server closet, or a load-bearing steel connection nobody wants exposed to moisture.
This is the second post in our week-long series on roof and building envelope inspections ahead of fall. Yesterday we covered the broader case for why late August and early September is the inspection window that matters most in this region. Today we're getting specific: a walkable, 14-point checklist you or your roofing contractor should be running on every low-slope roof in your portfolio in the next few weeks, along with what each finding actually means for your fall risk.
This isn't a generic "check for debris" list. It's built around the failure modes we see repeatedly on Bay Area low-slope roofs: the ones that turn a $400 membrane patch into a $30,000 interior remediation job because they went unnoticed for one more season.
Start with the field of the membrane itself, not just the edges. On TPO roofs, the failure pattern to watch for is shrinkage: TPO sheets pull away from parapet walls, curbs, and penetrations over 12-15 years of thermal cycling, and that pull creates tension on every seam and flashing detail on the roof. Walk the perimeter within three feet of every wall and curb and look for visible gaps, ridging, or a membrane surface that looks stretched tight rather than lying flat.
On EPDM roofs, the concern is different: check for shrinkage-related seam separation at the T-joints (where three pieces of membrane meet) and for granule loss or surface chalking that signals the rubber is past its UV-protective coating life. A quick water-bead test tells you a lot: if water sheets off a section instead of beading, the surface is oxidizing.
For modified bitumen, look for blistering, bubbles under the cap sheet where moisture or trapped air has separated the layers, and check granule loss along the south- and west-facing slopes, which take the brunt of California's UV load. Photograph every anomaly with a location reference (nearest RTU, drain, or parapet corner) so your roofing contractor isn't guessing later what "the soft spot near the northeast corner" actually referred to.
Roof penetrations (HVAC curbs, exhaust vents, conduit runs, plumbing stacks, skylights) account for a disproportionate share of leaks relative to their square footage, because every penetration is a manufactured seam rather than continuous membrane. Inspect the pitch pans and boots around each one for cracking, UV-degraded sealant, or standing water pooled against the curb base. Pitch pans in particular are notorious: the sealant compound inside them has a functional life of about 3-5 years in this climate, and once it cracks, water tracks straight down the penetration into the building.
Rooftop HVAC units deserve their own pass. Check that curb flashing is still mechanically fastened and sealed on all four sides, and look underneath accessible platforms for signs the unit has been shifted or re-set by past service techs without the flashing being properly re-sealed afterward: this happens more often than facility managers expect, especially after a compressor swap or unit replacement where the roofing trade wasn't looped back in.
Don't skip abandoned penetrations. Buildings that have gone through multiple tenant improvements often have capped-off vent stacks or old satellite dish mounts still sitting on the roof. Every one of those is a potential leak point that isn't on anyone's current equipment list, which means it's also not on anyone's maintenance radar until it fails.
A roof membrane in excellent condition can still fail catastrophically if drainage isn't working, because ponding water accelerates every other degradation mechanism: UV breakdown, seam stress, and in freeze-adjacent microclimates like parts of the South Bay foothills, membrane fatigue from thermal cycling in standing water.
Locate every roof drain, scupper, and overflow drain on your roof plan and physically confirm each is clear, not just visually clear from a distance but clear of debris packed into the drain bowl itself: leaves, roofing granules, and in older buildings, degraded insulation board that's crumbled into the strainer. Remove and reinstall drain strainers/domes if they haven't been pulled in over a year; debris accumulates underneath them where you can't see it from above.
Check for ponding that persists more than 48 hours after a wash-down test: pour water from a hose at the roof's high points and time how long it takes to clear each low area. Any ponding lasting longer than that indicates a structural slope problem, not just a drainage clog, and that's a conversation for a roofing engineer, not just added drain maintenance. This is also the point in the inspection where you want to physically walk gutters and internal drain leaders where accessible, since undersized or crushed leader pipe is a common and invisible cause of "mystery" ceiling leaks that show up nowhere near the actual roof penetration.
Finally, check overflow scuppers and secondary drains specifically: most jurisdictions require them by code precisely because primary drains clog, and an inspection that only checks primary drains is checking half the system.
Base flashing where the roof membrane turns up a parapet wall or curb is the single most common leak origin point we encounter on service calls, more common than field membrane punctures. Inspect the termination bar and counterflashing along every parapet: look for fasteners backing out, sealant that's cracked or missing in sections longer than a few inches, and membrane that's pulled loose from the wall substrate below the termination line.
Parapet coping caps deserve a dedicated check. These metal caps sit on top of parapet walls and are held by concealed clips or exposed fasteners; wind uplift over years loosens the seams between coping sections, and once water gets behind a coping cap it runs down inside the wall cavity rather than across the roof surface: meaning it can show up as a wall stain two floors down with no obvious connection to the roof at all. Check that end caps and miter joints are still sealed, and look for any coping section that moves when you press on it by hand.
Also check wall-to-roof transitions at any rooftop mechanical screen walls or equipment enclosures: these are often added after original roof installation as part of a tenant improvement or rooftop solar project, and the flashing tie-in quality varies enormously depending on which contractor did the work and whether the original roofing manufacturer's warranty terms were followed. If your roof has a manufacturer warranty, confirm any post-installation modifications were done by a certified applicator: unauthorized penetrations are the single most common reason warranty claims get denied.
None of these 14 checkpoints require specialized equipment beyond a moisture meter, a camera, and a hose: but they do require someone who knows what a failing pitch pan looks like versus a cosmetically weathered one, and who can tell the difference between normal TPO shrinkage and shrinkage that's about to open a seam. Running this checklist in-house is possible for teams with roofing-trained staff; for most commercial portfolios, pairing an internal walk-through with an annual professional inspection from a roofing contractor gives you both the documentation and the expertise to catch what a visual pass alone will miss.
The goal isn't a perfect roof: it's a roof where every known deficiency has been triaged, prioritized, and either repaired or scheduled before the first atmospheric river event puts it to the test.
MAFM's roofing partners perform documented 14-point low-slope roof inspections with photo reporting and prioritized repair recommendations: schedule your pre-fall inspection before contractor calendars fill up in September.
Link back to Monday's post introducing the fall roof and envelope inspection series, and forward to later posts this week covering building envelope sealant/waterproofing checks and how to build a fall storm-readiness maintenance calendar.
National Roofing Contractors Association (NRCA) guidelines on low-slope roof maintenance inspections; FEMA's Technical Bulletin on roof drainage and ponding water risk mitigation.
MAFM offers comprehensive facility management solutions tailored to your business needs.
Get in Touch